您好,欢迎光临莱州聚峰机械有限公司网站! 郑重声明 购机 售后 聚峰官微

全国咨询热线

400-879-1999

您的位置: 首页 > 新闻资讯 > 行业新闻
自动上料搅拌车进料堵塞的处理步骤!
来源:https://www.cnzkjf.com/ 日期:2020-11-24
在运用自动上料搅拌车的时分要留意疏浚进料口,假如呈现梗塞的问题,应该怎样去处置,详细的步骤又是什么呢?下面中科搅拌车的小编给大家细致的引见一下。
In the use of automatic feeding mixer, attention should be paid to dredging the inlet. If there is a problem of blockage, how to deal with it and what are the detailed steps? Below, the small series of China Science and technology mixer gives you a detailed introduction.
今天我们会为大家带来自动上料搅拌车的清洗要点,希望经过我们的引见让您对问题有更深化的理解
Today, we will bring you the cleaning points of automatic feeding mixer. We hope that through our introduction, you can have a deeper understanding of the problem
由于混凝土会在短时间内凝固成硬块,且对钢材和油漆有一定的腐蚀性,所以每次运用混凝土贮罐后,洗净粘附在混凝土贮罐及进出料口上的混凝土是每日维护必需认真停止的工作。其中包括:
Because the concrete will solidify into a hard block in a short time, and has certain corrosivity to steel and paint, so cleaning the concrete adhered to the concrete storage tank and the inlet and outlet after each use of the concrete tank is a daily maintenance work that must be seriously stopped. These include:
1.每次装料前用水冲洗进料口,使进料口在装料时坚持潮湿;
1. Flush the feed inlet with water before each loading to keep it moist during loading;
               中科搅拌车
2.在装料的同时向随车自带的清洗用水水箱中注满水;
2. At the same time of loading, fill the cleaning water tank attached with the vehicle with water;
3.装料后冲洗进料口,洗净进料口左近残留的混凝土;
3. After loading, wash the inlet and clean the residual concrete near the inlet;
4.到工地卸料后,冲洗出料槽,然后向混凝土贮罐内加清洗用水30—40 L;在车辆回程时坚持混凝土贮罐正向慢速转动;
4. After unloading at the construction site, wash the discharge tank, and then add 30-40 l of cleaning water into the concrete storage tank; when the vehicle returns, the concrete storage tank should rotate slowly in positive direction;
5.下次装料前切记放掉混凝土贮罐内的污水;
5. Remember to discharge the sewage in the concrete tank before the next loading;
6.每天收工时彻底清洗混凝土贮罐及进出料口四周自动,自动上料搅拌车的清洗要点保证不粘有水泥及混凝土结块。
6. At the end of each day, the concrete storage tank and the surrounding areas of the material inlet and outlet shall be thoroughly cleaned. The cleaning points of the automatic feeding mixer shall ensure that there is no cement and concrete caking.
1、上下料时间参数不合理:自动上料机因料仓内无法加装料位机,所以行业根本都有时间控制。如何设置时间参数,上下料时间设置其实很简单,在初次运用时,先设置一个小的时分,然后依据每次吸料位置渐渐加,当到达料位到达吸料口的时间,再减去一秒就是合理时间。放料时间是确保放完料再加一秒。这样做有两个益处:一是料位太高对滤芯伤害特别大,二是每次料都能放洁净。
1. Unreasonable loading and unloading time parameters: automatic feeding machine can not be installed in the silo, so the industry has time control. When the first feeding position is reached, it is easy to set the feeding time according to the reasonable feeding time. The discharging time is to ensure that one second is added after discharging. This has two benefits: one is that the material level is too high to damage the filter element; the other is that the material can be put clean every time.
2、自动上料搅拌车进料口给料量能否合理:正确的方式是物料在吸料口和空气构成一定的气物混合比,在气流的推进下平均流入上料机。这个时分我们需求将料枪设计带有补气功用。假如物料积压时间过长可能很硬,这个时分需求在料枪上装一个振荡器,敲碎结块的物料。
2. Whether the feeding amount at the feeding port of the automatic feeding mixer is reasonable: the correct way is to form a certain air-material mixing ratio between the material at the suction port and the air, and flow into the feeding machine on average under the promotion of the air flow. At this time, we need to design the material gun with air replenishing function. If the material overstocking time is too long, it may be very hard. At this time, we need to install an oscillator on the material gun to break the agglomerated materials.
以上就是关于自动上料搅拌车进料堵塞的处理步骤的介绍,希望对大家有所帮助,如想了解更多内容欢迎点击官网:中科搅拌车https://www.cnzkjf.com
The above is about the automatic feeding mixer processing steps of blocking, I hope to help you, if you want to know more, welcome to click the official website: Zhongke mixer https://www.cnzkjf.com 。